2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

带扩张段构型超声速气流中横向射流数值模拟

针对带扩张段构型的发动机燃烧室,采用欧拉-拉格朗日仿真方法研究喷注方式、喷孔参数及隔离段燃烧室构型的改变对于射流雾化效果的影响,用以更好地指导发动机设计.结果表明,在保证发动机总体流量不变的条件下,喷孔孔径减小或者喷孔总数量减少使得液气动量通量比增大,有利于同时增大单孔射流穿透深度以及液滴展向宽度.贫燃工况下如当量比为0.7条件下,射流流量减小,混合效果可能变差.而在发动机结构设计方面,隔离段到燃烧室的过渡设计不宜采用大转角,15°转角是相对较为理想的设计方案.采用小角度突扩构型设计比渐扩构型更容易找到相对好的点火位置.     

基于ANSYS的脱溶机转子结构有限元分析及优化

大豆粕低温脱溶过程中,传统脱溶机转子的辐条式端板结构易出现疲劳断裂。通过对脱溶机转子辐条式端板的结构研究,建立力学模型,采用ANSYS软件对转子辐条式端板进行有限元分析,模拟辐条各截面上应力的变化,确定端板辐条应力集中位置。为该转子端板结构的改进方案提供理论依据。     

Optical in-process height measurement system for process control of laser metal-wire deposition

We propose an in-process height measurement system for a weld bead and feedback control system for wire-feeding speed for high-quality laser deposition. Metal additive manufacturing, especially laser metal-wire deposition, is effective for complex shape fabrication and repair processing. However, we must control the gap between a weld bead and a feed wire in an optimal range for high-quality deposition. Conventionally, the Z-stage pitch for multi-layer deposition must be precisely adjusted by each deposition shape. In this paper, we design an in-process height measurement system that is integrated in a laser processing head, which measures the weld bead height by a line section method. We decreased the influence of the intense thermal radiation generated from a melt pool by inserting the band-pass filter of the line beam's wavelength in the imaging system and optimizing its line laser power. Consequently, our system can measure the weld bead height near the melt pool, which is 4 mm in front of it. Next we show that our proposed system can measure the weld bead height during wire-laser metal deposition with 50-μm accuracy by comparing its value to the true value. Finally, we achieved a cylinder shape deposition of 50-mm height, regardless of the Z-stage pitch and the cylinder diameter of the multi-layer deposition, by controlling the wire-feeding speed based on the measured weld bead height.     

低剂量抑制剂Inhibex501存在下的甲烷水合物相平衡研究

含动力学抑制剂的天然气水合物相平衡研究对新型低剂量抑制剂的开发具有指导作用。在283.6 ~ 290.9 K和7.51 MPa ~ 15.97 MPa的温压范围内研究了抑制剂Inhibex501及其溶剂2-乙二醇单丁醚对甲烷水合物相平衡条件的影响。实验结果显示，0.5wt%和2.0wt%浓度的Inhibex501对甲烷水合物形成的热力学条件具有促进作用，能使甲烷水合物形成移向更高的温度或者更低的压力，而2-乙二醇单丁醚在浓度0.2wt% ~ 1.0wt%范围几乎不改变甲烷水合物形成的热力学条件，N-乙烯基己内酰胺与N-乙烯基吡咯烷酮的共聚物对水合物形成热力学条件的改变起主要作用。     

超高压水力割缝增透卸压规律研究与应用

运用FLAC3D软件模拟不同割缝压力和割缝间距条件下,钻孔周围煤体应力分布特征,分析了穿层钻孔水力割缝煤体卸压规律。通过在赵固二矿实施超高压水力割缝增透技术工艺,有效解决了单一低渗坚硬厚煤层瓦斯抽采技术难题,增大了抽采钻孔卸压范围,大幅提高了煤体透气性。     

300MWCFB锅炉配套半干法烟气脱硫的汞排放试验研究

某300 MW循环流化床(CFB)锅炉采用炉内脱硫、SNCR、预电除尘器和烟气循环流化床半干法脱硫装置实现了超低排放。对不同工况下不同位置的烟气汞浓度和灰渣等固体副产物中的汞含量进行测试分析,研究结果表明:燃煤在循环流化床锅炉燃烧产生的汞主要以气态汞和颗粒汞形式存在;锅炉负荷提高,烟气中气态汞和颗粒汞浓度均有所提高,炉内脱硫对原始汞排放特性几乎没有影响;烟气循环流化床半干法脱硫装置可脱除71%～77%的气态汞和86%～88%的颗粒汞;采用预电除尘器与烟气循环流化床半干法脱硫结合的超低排放路线,总汞脱除率可达到82%～87%,使烟囱排放的汞浓度不高于1.5μg/m~3。副产物分析结果表明,烟气中脱除的汞主要富集于粉煤灰和半干法脱硫灰中。     

基于ANSYS及加速寿命试验台对油缸单耳环活塞杆杆头断裂进行设计改进

该文对某工程机械油缸单耳环活塞杆杆头断裂进行失效分析,提出了在毛坯锻造工艺满足设计要求的条件下,单耳环活塞杆杆头变截面处应力集中导致残余应力过大,是单耳环活塞杆杆头断裂的主要原因。从这方面出发,优化了单耳环活塞杆杆头变截面处的残余应力,通过ANSYS软件对优化后的结构进行应力分析,并用油缸加速寿命可靠性试验台做2F台架实验和整机多批次小批量试装来验证改进措施的有效性,最终提高了油缸单耳环活塞杆杆头在极限工况下抗疲劳的强度。     

铜山口铜矿坑内钻勘探的生产实践

随着铜山口铜矿地下深部基建结束，坑道探矿存在安全事故隐患、地质取样质量无法保证的问题，为了加快生产探矿，发挥坑内钻优势，弥补坑道探矿不足，购置了3台坑内钻进行探矿。通过在主矿体生产探矿及周边扫盲增储、尖灭矿体探边摸底、零星小矿体追寻、超前探水、指导巷道掘进方向等应用，结果表明，坑内钻具有操作灵活机动，易掌握，缩短了生产探矿时间，节约探矿成本，作业现场安全等优势，保持了三级矿量的动态平衡，确保了生产持续稳产发展。     

Inorganic thermoelectric materials: A review

Thermoelectric generator, which converts heat into electrical energy, has great potential to power portable devices. Nevertheless, the efficiency of a thermoelectric generator suffers due to inefficient thermoelectric material performance. In the last two decades, the performance of inorganic thermoelectric materials has been significantly advanced through rigorous efforts and novel techniques. In this review, major issues and recent advancements that are associated with the efficiency of inorganic thermoelectric materials are encapsulated. In addition, miscellaneous optimization strategies, such as band engineering, energy filtering, modulation doping, and low dimensional materials to improve the performance of inorganic thermoelectric materials are reported. The methodological reviews and analyses showed that all these techniques have significantly enhanced the Seebeck coefficient, electrical conductivity, and reduced the thermal conductivity, consequently, improved ZT value to 2.42, 2.6, and 1.85 for near-room, medium, and high temperature inorganic thermoelectric material, respectively. Moreover, this review also focuses on the performance of silicon nanowires and their common fabrication techniques, which have the potential for thermoelectric power generation. Finally, the key outcomes along with future directions from this review are discussed at the end of this article.